Measure once. Buy with a plan.

Board Foot Calculator

From a single shelf to a hardwood tabletop. Calculate lumber volume, plan a cut list, estimate slabs and logs, or convert board feet to linear feet—with editable waste and costs.

Hardwood boards with a tape measure, carpenter’s pencil and combination square on a workbench

Your lumber

Use the dimensions your supplier tallies, or actual measurements to estimate physical volume. Decimal feet accepted: 8 ft 6 in = 8.5 ft.

Waste & optional cost

Waste percentages and species prices are editable planning examples, not grading standards or current market quotes. Currency selection does not convert prices. Enter your supplier’s quote; tax, delivery and milling are excluded.

Quick answer: Board feet = thickness (in) × width (in) × length (ft) ÷ 12. A nominal 2×4 at 8 feet is 5.33 BF. Ten 1×6 boards at 8 feet total 40 BF; with 15% waste, the buying target is 46 BF.

Source and calculation review: Live Decor Well · . Estimates are not a certified lumber tally or structural design.

How to use the board foot calculator

Choose the mode that matches what you are buying: boards, a project cut list, a live-edge slab or a log. Enter dimensions in the selected units, then add quantity, an optional waste allowance and your quoted price. Read the measurement notes before treating an estimate as a lumber-yard invoice.

1. Choose your measurement basis. For standard softwood tally use nominal size; for physical volume use actual size. For hardwood ask which rough thickness and width the supplier bills.

2. Enter your dimensions and quantity. Project mode also needs stock length, saw kerf and combined end trim. Metric thickness and width can use millimetres or centimetres; length is in metres. Unit changes preserve the original dimensions.

3. Review the result, allowance and optional cost. In Project mode, inspect the crosscut layout and download the shopping list. Match the final order to available stock and your supplier’s tally.

What is a board foot?

A board foot is 144 cubic inches of volume, equivalent to a board 1 inch thick, 12 inches wide and 12 inches long. It describes an amount of wood rather than one particular board shape. Twelve board feet make a cubic foot, regardless of the species.

A board foot is not a cube one foot on every side: that cube contains 12 board feet. Prices by BF can compare different cross-sections, but grade, drying and milling still matter. Nominal tally volume and actual dressed volume are not interchangeable.

How to calculate board feet

Multiply thickness in inches by width in inches by length in feet, then divide by 12. If every measurement is in inches, divide the product by 144 instead. Apply quantity to the unrounded result. For a purchase allowance, multiply that total by one plus the waste percentage divided by 100.

Worked examples using the stated dimensions, rounded only for display.
Entered sizeCalculationBoard feet
1×6 × 8 ft1 × 6 × 8 ÷ 124
2×4 × 8 ft2 × 4 × 8 ÷ 125.33
2×6 × 8 ft2 × 6 × 8 ÷ 128
1×12 × 8 ft1 × 12 × 8 ÷ 128
2×12 × 16 ft2 × 12 × 16 ÷ 1232

Board feet of common lumber sizes

The chart below shows board feet from nominal thickness and width at four common lengths. Use it for a quick comparison or a nominal lumber tally, not for the exact physical volume of surfaced boards. Multiply a cell by the number of identical boards, and keep waste separate.

Nominal board-foot chart; quantities in BF, not linear feet.
Nominal size (in)8 ft10 ft12 ft16 ft
1×42.673.3345.33
1×64568
1×85.336.67810.67
1×106.678.331013.33
1×128101216
2×45.336.67810.67
2×68101216
2×810.6713.331621.33
2×1013.3316.672026.67
2×1216202432
4×410.6713.331621.33

Nominal vs actual lumber size

Nominal dimensions are size names used for standard softwood board-measure tallies; dressed dimensions describe the finished board. A nominal 2×4 is usually 1½ by 3½ inches when dry and surfaced. Use actual measurements for physical volume, and ask the yard which dimensions and tally method apply to a hardwood purchase.

Selected dry surfaced sizes from PS 20-25; green sizes, moisture changes and nonstandard products differ.
Nominal size (in)Minimum dry dressed size (in)
1×4¾ × 3½
1×6¾ × 5½
1×8¾ × 7¼
1×12¾ × 11¼
2×41½ × 3½
2×61½ × 5½
2×81½ × 7¼
2×101½ × 9¼
2×121½ × 11¼
4×43½ × 3½

At 8 feet, the nominal 2×4 calculation is 5.33 BF; its 1½ × 3½ inch physical size gives 3.5 BF. Neither number is universally wrong: identify what is being measured. The calculator never changes your entered dimensions silently.

Yard tally is not universally rounded upward to a quarter or half foot. Standards specify different rounding and measurement conventions. This tool keeps exact geometric math until display; it does not reproduce an NHLA inspection tally or every supplier’s invoice.

Reference: NIST American Softwood Lumber Standard PS 20-25, measurement and tally provisions and dry dressed size tables.

Hardwood quarters: 4/4, 5/4 and 8/4

Hardwood quarters express rough thickness in quarter-inch increments: 4/4 is 1 inch, 5/4 is 1¼ inches and 8/4 is 2 inches. The thickness after surfacing is smaller and varies. When estimating a bill, enter the supplier’s billed thickness; when planning finished parts, leave enough wood for milling.

Quarter designations describe rough thickness, not a guaranteed finished size.
Quarter designationNominal rough thickness (in)Metric equivalent (mm)
4/4125.4
5/41.2531.75
6/41.538.099999999999994
8/4250.8
12/4376.19999999999999
16/44101.6

For example, a seller may offer surfaced 4/4 at approximately 13/16 inch. That is a product specification to verify, not a universal promise. For a true 2-inch finished tabletop, ask whether thicker rough stock is necessary.

References: NHLA grading rules and AHEC’s hardwood measurement guide. Supplier agreements and applicable grading rules govern billing.

Board foot calculator with waste: how much should I add?

Start with an allowance matched to your project, then adjust it for the actual boards available. Ten percent for framing, fifteen percent for a short-parts list and fifteen to thirty percent for rough hardwood are illustrative starting points. Defects, grain matching, milling and unusable offcuts can require a different allowance.

Editable planning assumptions, not grade guarantees or published grading requirements.
ProjectStarting allowanceCheck before ordering
Straightforward framing10%Cuts, damaged ends, stock lengths
Many short parts15%Kerf, end trim and offcut reuse
Rough hardwood15–30%Knots, checks, milling and grain selection

Project mode groups matching cross-sections and fits the longest parts first. It accounts for saw kerf and a combined end-trim allowance per stock board. For each group it chooses the greater of the packed board count or the waste-adjusted volume requirement. It does not add waste twice.

This is a one-dimensional crosscut estimate. It does not rip multiple widths from one wide board, match grain, inspect defects or guarantee the fewest possible boards. Finished part sizes need rough-stock allowances before entry.

Board foot vs linear foot: convert between them

A linear foot measures length; a board foot measures volume. To convert linear feet into board feet, multiply by thickness and width in inches and divide by twelve. Reverse that operation to find linear feet. The numbers match only when the thickness-times-width product is twelve square inches.

Conversions use the stated thickness and width.
Size and lengthLinear feetBoard feetBF per linear foot
1×6 × 8 ft840.5
1×12 × 8 ft881
2×6 × 10 ft10101
2×12 × 16 ft16322

LF = BF × 12 ÷ (thickness × width). Forty board feet of 1×6 corresponds to 80 linear feet. For board feet to cubic feet, divide by 12. For cubic metres, multiply by exactly 0.002359737216; 1 m³ is approximately 423.776 BF.

Estimate live edge slab board feet

For a slab with a fairly regular taper, average the usable widths at its two ends and use that average in the board-foot formula. For an irregular edge, take additional measurements along its length. This gives a volume estimate; a fixed-width top must still fit through the slab’s narrowest usable point.

An 8-foot slab, 2 inches thick, with end widths of 20 and 28 inches averages 24 inches wide. Its estimate is 2 × 24 × 8 ÷ 12 = 32 BF, before waste. Adding 20% gives 38.4 BF as a buying target.

The optional third measurement uses the arithmetic mean of end A, middle and end B. More samples or dividing the slab into smaller sections may be better for deep curves. Bark, cracks and holes should not be counted as usable furniture material. The seller may price the slab individually.

Log scales: Doyle, Scribner and International ¼-inch

A log rule estimates sawn lumber output from a log, rather than measuring the log as a solid cylinder. Different rules make different assumptions about processing losses. Enter small-end diameter inside bark and nominal log length, then choose the rule agreed with the buyer; do not compare prices across rules without converting the basis.

Doyle: (D − 4)² × L ÷ 16. Scribner formula estimate: (0.79D² − 2D − 4) × L ÷ 16. D is inches inside bark at the small end and L is feet. The Scribner approximation is not an exact Decimal C table lookup.

International ¼-inch uses separate published equations at 4, 8, 12, 16 and 20 ft. At 16 ft, BF = 0.796D² − 1.375D − 1.23, rounded to the nearest 5 BF. For a 16-inch diameter, 16-foot log: Doyle gives 144 BF, Scribner formula gives 166.24 BF and International gives 180 BF.

Our International coefficients follow USDA Forest Service GTR-SRS-251. Scribner follows the Forest Service formula research note and the length-scaled Tennessee Extension approximation. The calculator excludes defect deductions, long-log segmentation and regional table variants. A professional scaling agreement controls a sale.

References: USDA Forest Service GTR-SRS-251, The Formula Scribner Log Rule, and Tennessee Extension’s Understanding Log Scales and Log Rules.

What does lumber cost per board foot?

Multiply the board feet you expect to buy by a price quoted on the same measurement basis. Species alone does not determine cost: thickness, grade, drying, milling and local supply also matter. The amounts below are editable budgeting examples from the brief, not verified current market prices or regional price ranges.

Example inputs only. Replace them with a dated supplier quote.
SpeciesIllustrative US$/BF
Pine$2
Cedar$4
Maple$5
Red oak$6
Cherry$8
Walnut$12

At a hypothetical US$6/BF, 40 BF of red oak costs US$240 before waste; 46 BF with a 15% allowance costs US$276. Project mode prices the whole stock boards it recommends, which can exceed a simple percentage allowance.

Canadian users can select CAD and enter a local quote. Changing the currency label does not convert a US price. Delivery, tax, surfacing, freight minimums and any slab-specific pricing remain separate.

Put the measurements to work

Follow our step-by-step how to calculate board feet guide, or compare board foot vs linear foot before ordering. For project inspiration, explore live-edge coffee tables and wood kitchen shelving.

Planning the whole room? Estimate finishes with the paint calculator and surfaces with the tile calculator. For a patterned feature wall, use the wallpaper calculator.

Board feet calculator FAQ

What is a board foot?

A board foot is a lumber-volume unit equal to 144 cubic inches: a piece 1 inch thick, 12 inches wide and 12 inches long. It is not a length. Twelve board feet equal one cubic foot; the same volume can have many different shapes.

How many board feet are in a 2x4?

A nominal 2×4 that is 8 feet long contains 5.33 board feet by nominal tally: 2 × 4 × 8 ÷ 12. Its typical dry dressed dimensions are 1½ × 3½ inches, equivalent to 3.5 board feet of physical wood. These answer different questions.

How do I calculate board feet?

Multiply thickness in inches by width in inches by length in feet, then divide by 12. Multiply by quantity for identical boards. If all three measurements are in inches, divide by 144 instead. Keep full precision until the total, then apply any selected buying allowance.

What is board foot vs linear foot?

A board foot measures volume, while a linear foot measures length. To convert, you also need thickness and width. One linear foot of 1×6 stock is 0.5 board feet; one linear foot of 2×12 stock is 2 board feet, using the stated dimensions.

How much waste should I add?

Try 10% for straightforward framing, 15% for a short-parts cut list, or 15–30% for rough hardwood as planning starting points. These are not grading rules. Defects, grain selection, stock lengths and milling losses can change the amount; a cut layout is more useful than a percentage alone.

Should a board feet calculator use nominal or actual dimensions?

Use the measurement basis for your task. Standard softwood board-measure tallies use nominal dimensions; physical-volume estimates use actual dimensions. Random-width hardwood requires the supplier’s rough-thickness and width/tally conventions. The calculator uses exactly what you enter and does not automatically turn a dressed measurement into a nominal one.

What is 4/4 lumber?

Four-quarter, written 4/4, denotes a nominal rough thickness of 1 inch. Similarly, 8/4 means 2 inches and 12/4 means 3 inches. Surfaced thickness depends on the supplier and milling. Select the billed rough thickness for a purchase estimate and check the finished thickness your project needs.

How many board feet are in a cubic foot?

There are exactly 12 board feet in one cubic foot. Divide board feet by 12 to get cubic feet, or multiply cubic feet by 12 to get board feet. One board foot is exactly 0.002359737216 cubic metres, so a cubic metre is about 423.776 board feet.

How do I calculate board feet for a live-edge slab?

For a simple taper, average the usable widths at both ends, then multiply that width in inches by thickness in inches and length in feet, and divide by 12. For an irregular slab, sample more widths. Bark, voids and a narrow middle can reduce usable material.

What is the Doyle rule?

The Doyle rule estimates sawn board feet from a log using (D − 4)² × L ÷ 16, where D is the small-end diameter inside bark in inches and L is log length in feet. A 16-inch-diameter, 16-foot log scales 144 BF before defect deductions.

How much does a board foot of walnut cost?

There is no single walnut price: grade, thickness, drying, region and milling all matter. This tool offers US$12 per board foot only as an editable example, not a current quote. Replace it with your supplier’s price and confirm whether delivery, tax and surfacing are additional.

How many board feet do I need for a table top?

A top measuring 72 × 36 × 2 inches has a net volume of 36 board feet. Adding 15–30% gives 41.4–46.8 BF before whole-board selection. If 2 inches is the finished thickness, choose rough stock thick enough to allow for planing; 8/4 may finish thinner.

Found an issue? Send us your dimensions, mode and expected result so we can check it.